we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. jumbo-led 15.11.2007 rev. 02 radiation infrared outline: h = 13 mm ( 0.5) d = 16 mm ( 0.5) thread m10 pin 1 ? cathode pin 2 ? anode absolute maximum ratings at t amb = 25c, on heat sink (s 200 cm2), unless otherwise specified symbol value unit i f 1.1 a i fm 2,0 a p2w t amb -25 to +100 c t stg -25 to +100 c t j 100 c electrical characteristics t amb = 25c, unless otherwise specified parameter test conditions symbol min typ max unit forward voltage i f = 350 ma v f 1.5 2.0 v forward voltage* i f = 1000 ma v f 1.9 v switching time i f = 350 ma t r , t f 100 ns reverse voltage i r = 100 a v r 5 thermal resistance junction-case r thjc 10 k/w *only recommended on optimal heat sink on heat sink on heat sink on heat sink on heat sink operating temperature range storage temperature range junction temperature 2 w on heat sink t p 10 s, f 500 hz ELJ-810-619 case technology type applications medical appliances, remote control and optical communications, light barriers, measurement systems test onditions algaas/gaalas plastic lens, metal case high-power infrared led with narrow beam angle, with aluminium case and thread socket for easy handling and heat sink mounting description parameter dc forward current peak forward current power dissipation ?16 m10 8 2 1,5 5,08 ?1,7 8,5 4,5 ?11 ?12,5 13 2 1 12 epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 1 of 5
we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. jumbo-led 15.11.2007 rev. 02 ELJ-810-619 optical characteristics at t amb = 25c, on heat sink (s 200 cm2), unless otherwise specified parameter test conditions symbol min typ max unit radiant power i f = 350 ma e 50 85 mw radiant power* i f = 1000 ma e 220 mw radiant intensity i f = 350 ma e 800 1200 mw/sr radiant intensity* i f = 1000 ma e 3300 mw/sr peak wavelength i f = 350 ma p 800 810 820 nm spectral bandwidth at 50% i f = 350 ma ? 0,5 30 nm viewing angle i f = 350 ma ? 10 deg *only recommended on optimal heat sink note: all measurements carried out with epigap equipment, on blank aluminium heat sink, s = 180 cm2, passive cooling. measurement results and curve characteristics obtained with other heat sinks may differ. 0 200 400 600 800 1000 0 1 2 3 e (rel.) i f (ma) radiant power vs. forward current (typical) normalized to e @ i f = 350 ma 0 200 400 600 800 1000 0.0 0.5 1.0 1.5 2.0 2.5 i f (ma) u f (v) forward current vs. forward voltage (typical) epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 2 of 5
we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. jumbo-led 15.11.2007 rev. 02 ELJ-810-619 500 600 700 800 900 1000 1100 0.0 0.2 0.4 0.6 0.8 1.0 rel. intensity (arb. units) wavelength (nm) spectral power distribution (typical) at i f = 20 ma 0 200 400 600 800 1000 -3 0 3 6 wavelength shift (nm) i f (ma) typical wavelength shift vs. forward current (rel. to p @ i f = 350 ma) 0 20406080100120 0.0 0.2 0.4 0.6 0.8 1.0 1.2 max. forward current (a) ambient temperature (c) ambient temperature vs. maximal forward current epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 3 of 5
we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. jumbo-led 15.11.2007 rev. 02 ELJ-810-619 remarks concerning optical radiation safety* i f < 350ma i f > 350ma *note: safety classification of an optical component mainly depends on the intended application and the way the component is being used. furthermore, all statements made to classification are based on calculations and are only valid for this led "as it is", and at continuous operation. using pulsed current or altering the light beam with additional optics may lead to different safety classifications. therefore these remarks should be taken as recommendation and guideline only. if intended to operate at higher continuous current (>350 ma), this product has to be (potentially) classified as class 3b led. class 3b leds may have sufficient power to cause an eye injury, both from the direct beam and from reflections,so these products are therefore considered hazardous to the eye. however, the extent and severity of any eye injury arising from an exposure to the light beam of a class 3b product will depend upon several factors including the radiant power entering the eye and the duration of the exposure. nontheless, adequate precautions should be taken to avoid direct or indirect viewing into the beam.. up to a forward current of 350 ma, at continous operation, this product may be classified as led product class 1m , according to standard iec 60825-1:a2. class 1m products are safe to eyes and skin under normal conditions, including when users view the light beam directly. class 1m products produce either a highly divergent beam or a large diameter beam,so only a small part of the whole light beam can enter the eye. however, such optical products can be harmful to the retina if the beam is viewed using magnifying optical instruments. therefore, users should not incorporate optics that could concentrate the output into the eyes. infrared radiation accord. din en/iec 60825-1:2001-11 do not view directly with optical instruments led class 1m infrared radiation accord. din en/iec 60825-1:2001-11 do not expose to the beam led class 3b epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 4 of 5
we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. jumbo-led 15.11.2007 rev. 02 ELJ-810-619 handling precautions e) leds are static sensitive devices, so adequate handling precautions have to be taken, e.g. wearing grounding wrist straps. to prevent damage to the led during soldering and assembly, following precautions have to be taken into account. a) the bending point of the lead frame should be located at least 2.5 mm away from the body. b) while bending, the base of the lead frame has to be fixed with radio pliers or similar. c) to ensure an adequate strain relief, the lead frames have to be firmly fixed during soldering. d) avoid any torsion or tensile loading of the lead frames, especially when they have been heated after being soldered. epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 5 of 5
|
